Chicago Metro · 16 towns covered
Whole House Rewiring in the Chicago suburbs
Rewiring is the largest electrical project a house will ever have, and it is almost always driven by one of three things: knob-and-tube wiring an insurer will no longer cover, aluminium branch circuits from the late 1960s and early 1970s, or cloth-insulated conductors that have gone brittle enough to crumble when touched. Older Fox Valley housing stock has all three, sometimes in the same building.
- $8,000 – $30,000+ typical across the metro
- Permitted and inspected
- Northwest suburbs & Fox Valley
- 16 towns covered
KilowattBros is a free matching service. All electrical work is performed by independent, licensed contractors.
Licensed & insured
Work is carried out by licensed, insured electrical contractors — never by us.
Fast hand-off
Your request reaches a contractor the moment you submit it, not a queue.
One contractor
Not a shared lead resold to five companies who all call you at once.
Free, no obligation
Matching costs you nothing. Contractors pay us, and only after you book.
Whole House Rewiring in the Chicago suburbs: the short answer
- Typical cost
- $8,000 – $30,000+
- Whole House Rewiring in the Chicago suburbs typically costs $8,000 – $30,000+. The figure depends on your home's existing wiring and access.
- How long it takes
- One to three weeks depending on size, access, and occupancy
- One to three weeks depending on size, access, and occupancy. Permit review and inspection scheduling usually set the calendar timeline rather than the electrician's availability.
- Permit required
- Yes
- Whole House Rewiring requires a permit and inspection in every municipality we cover. Your electrician normally pulls it.
Figures are typical ranges for planning, not a quote. Only a licensed electrician who has seen the job can price it.
Cost
What whole house rewiring costs around Chicago
These are Illinois figures, not national averages. Labour and permit costs in the Chicago metro run above the national median, and a page quoting a US-wide number will consistently under-estimate what you are actually quoted here.
| Scope of work | Typical range | What moves the price |
|---|---|---|
| Partial rewire, knob-and-tube removal on affected circuitsCommon where K&T survives only in part of the house. | $4,000 – $12,000 | Common where K&T survives only in part of the house. |
| Full rewire, 1,000–1,500 sq ft single storeyIncludes new panel in most cases. | $8,000 – $16,000 | Includes new panel in most cases. |
| Full rewire, 2,000–2,800 sq ft two storeySecond-storey access is the main cost driver. | $15,000 – $28,000 | Second-storey access is the main cost driver. |
| Aluminium branch wiring remediation (AlumiConn / COPALUM)Far cheaper than a full rewire and accepted by most insurers. | $2,500 – $8,000 | Far cheaper than a full rewire and accepted by most insurers. |
| Plaster and drywall repair after rewiringFrequently quoted separately — confirm who owns it. | $2,000 – $8,000 | Frequently quoted separately — confirm who owns it. |
| Panel replacement as part of the rewireNearly always done at the same time. | $2,200 – $4,800 | Nearly always done at the same time. |
| Permit and inspectionsMulti-stage inspections; often fee-scaled to project value. | $200 – $900 | Multi-stage inspections; often fee-scaled to project value. |
Ranges reflect typical Chicago-area pricing and are for planning only — they are not a quote. Actual cost depends on your home, your existing wiring, and the permit requirements in your municipality. Only a licensed electrician who has seen the job can price it.
Do you actually need this?
Signs it is time for whole house rewiring
None of these on their own proves you need work done. Several together usually does. If you recognise two or more, it is worth having a licensed electrician look before it becomes an emergency call.
- Ceramic knob-and-tube insulators visible in the attic or basement
- Two-prong ungrounded outlets throughout the house
- Cloth-covered wiring that flakes or crumbles when moved
- Aluminium branch wiring — the house was built 1965 to 1974
- An insurer has declined coverage or demanded remediation
- Warm switch or outlet cover plates
- Repeated flickering across multiple unrelated circuits
- Extension cords doing permanent duty because there are no outlets
What a proper job includes
What to expect from a whole house rewiring
Use this as a checklist when you compare quotes. A quote that is noticeably cheaper than the others is usually missing something on this list — most often the permit, the inspection, or the grounding.
- Timeline
- One to three weeks depending on size, access, and occupancy
- Permit
- Required
- 01Full assessment and circuit-by-circuit mapping before quoting
- 02Staged permit with rough-in and final inspections
- 03New branch circuits in NM-B cable, properly grounded throughout
- 04Current-code outlet spacing, AFCI and GFCI protection, tamper-resistant devices
- 05Dedicated circuits for kitchen, laundry, bathroom, and HVAC loads
- 06Panel replacement and full circuit labelling
- 07Old conductors removed rather than abandoned in place where accessible
- 08Documented inspection sign-off for insurance and resale
Permits & code
What the rules actually require
A rewire is permitted and inspected in stages — rough-in before anything is closed up, then final. Homes in a designated historic district, which includes a substantial part of Elgin, may also need design review before exterior-visible work proceeds. Build that review time into the schedule rather than discovering it mid-project.
Knob-and-tube was designed to shed heat into open air. Burying it in blown-in attic insulation — which happened to a great many suburban Chicago houses during 1970s and 2000s efficiency retrofits — traps that heat against conductors with no ground path. That combination, not the age of the wiring alone, is what most concerns insurers.
Aluminium branch wiring from roughly 1965 to 1974 is not inherently unsafe, but aluminium expands and contracts more than copper and oxidises at terminations, so connections loosen over time. Full replacement is rarely necessary — CPSC-recognised repairs such as COPALUM crimps or AlumiConn connectors at every device are the accepted remediation and cost a fraction of a rewire.
Rewiring an occupied house is done in sections so the family keeps power. Expect access to walls, closets, and ceilings in rotation, and settle who is responsible for plaster and drywall repair in writing before work starts — this is the most common source of dispute on rewire projects.
Pick your town for local detail
Whole House Rewiring by town
16 towns across the northwest suburbs and Fox Valley. Each town page covers rewiring alongside its own permit authority, utility and housing history — because a 1962 Streamwood ranch and a 2003 Huntley build have almost nothing in common electrically.
- ElginKane County
- South ElginKane County
- StreamwoodCook County
- CarpentersvilleKane County
- West DundeeKane County
- BartlettCook County
- Hanover ParkCook County
- Hoffman EstatesCook County
- St. CharlesKane County
- AlgonquinMcHenry County
- SchaumburgCook County
- GenevaKane County
- HuntleyMcHenry County
- BataviaKane County
- AuroraKane County
- NapervilleDuPage County
Go deeper
What whole house rewiring costs, in detail
Illinois figures, the trade-offs, and what separates a complete quote from a cheap one.
FAQ
Whole House Rewiring — questions
How much does it cost to rewire a house near me?
In the Chicago suburbs, budget $8,000 to $16,000 for a 1,000 to 1,500 sq ft single-storey home and $15,000 to $28,000 for a larger two-storey. Access drives the number more than square footage — a house with a full basement and a walkable attic is far cheaper to rewire than a two-storey with finished plaster on both levels.
Do I have to rewire if I have knob-and-tube?
Not automatically. Knob-and-tube that is intact, not buried in insulation, and not extended with modern splices can still be serviceable. What usually forces the issue is insurance: several carriers writing in Illinois will not bind or renew a policy with active K&T. If your insurer is fine with it and an electrician has assessed it, a phased approach is legitimate.
Is aluminium wiring dangerous?
Aluminium branch wiring from the late 1960s and early 1970s needs attention but rarely needs full replacement. The failure point is the terminations, where expansion and oxidation loosen connections and generate heat. CPSC-recognised remediation — COPALUM crimps or AlumiConn connectors at every device — costs $2,500 to $8,000 rather than the price of a rewire and satisfies most insurers.
Can I stay in the house during a rewire?
Usually yes. Electricians work in sections and restore power to finished areas at the end of each day. It is dusty and disruptive, walls and closets get opened, and you will lose access to parts of the house in rotation, but most families stay put. A whole-house rewire on a tight timeline is the exception.
Will I need to repair drywall and plaster afterwards?
Yes, and you should establish in writing who is doing it. Some electrical contractors patch to a paint-ready finish, some leave neat openings for your own contractor, and some quote repair separately. In older plaster homes this can add $2,000 to $8,000 and it is the single most common source of surprise on a rewire.
How long does rewiring a house take?
One to three weeks of on-site work for a typical suburban home, plus inspection scheduling between the rough-in and final stages. Older homes with plaster walls, balloon framing, or historic district requirements sit at the longer end.
Does rewiring include a new electrical panel?
Almost always, and it should. New branch circuits landing in a 1960s fuse box or an obsolete panel wastes much of the benefit, and no inspector wants to see modern AFCI-required circuits terminating in equipment that cannot accept AFCI breakers. Check that the panel is in the quote rather than assumed.
Next step
Get matched with a licensed electrician
One short form. It goes straight to a licensed, insured contractor who works in your area — not into a national lead pool that resells it to five companies.
Or call +1 (727) 477-1356KilowattBros is a free matching service. All electrical work is performed by independent, licensed contractors.